haawi.blogg.se - Selected data does not fit into selected flash sectors

#Selected data does not fit into selected flash sectors plus#
#Selected data does not fit into selected flash sectors download#

Expenses: The lower the expense ratio, the less of your investment that is given over to administrative costs.

Volume: Trading volume over a particular period of time allows you to compare the popularity of different funds the higher the trading volume, the easier it may be to trade that fund.

Contents already match - Bank 0 0x00000000: Skipped. Start of comparing flash - CRC check was estimated as fastest method - Comparing range 0x0000 – 0xD5FF (107 Sectors, 53 KB), using multi-block CRC calculation - All CRCs match - Comparing range 0xF600 – 0xF7FF (1 Sector, 512 Bytes), using multi-block CRC calculation - All CRCs matchĠ2-0000001880-01F0: - Comparing range 0x0000 – 0xD5FF (107 Sectors, 53 KB), using alternative multi-block CRC calculation - All CRCs match - Comparing range 0xF600 – 0xF7FF (1 Sector, 512 Bytes), using alternative multi-block CRC calculation - All CRCs match - End of comparing flash - Start of erasing sectors - End of erasing sectors - Start of flash programming - End of flash programming - Start of verifying flash - End of verifying flash - Start of restoring - Restoring RAMCode - Restore targetĠ2-0000001882-012A: - Restore memory - Restoring CPU registers - End of restoring - Bank 0 0x00000000: Skipped.

#Selected data does not fit into selected flash sectors plus#

I’m using KDS (3.2.0) with Segger JLink Plus ( V622d ) on MKE02Z64xxx4 and I get the following silent error on the console:ĭownloading 82 bytes address 0x10000004 – Verify failedĭownloading 4 bytes address 0x10000058 – Verify failedĭownloading 52 bytes address 0x1000005C – Verify failedĭownloading 4 bytes address 0x10000090 – Verify failedĭownloading 40 bytes address 0x10000094 – Verify failedĠ3-0000001636-0029: Downloading 82 bytes address 0x10000004Ġ2-0000001681-01FA: T1768 001:637 JLINK_WriteMem(0x10000004, 0x0052 Bytes, …) – Data: 00 46 00 50 00 28 00 28 00 05 00 3C 00 46 A4 01 … - CPU_ReadMem(4 bytes 0圎000ED90) -– - Start of determining dirty areas in flash cache - End of determining dirty areas - Start of preparing flash programming - Calculating RAM usage - RAM usage = 4096 Bytes - Preserving CPU registers - Preparing memory - Determining CPU clock frequency - CPU frequency = 16021 kHz - Preparing targetĠ2-0000001794-01AC: - Downloading RAMCode - Checking target RAM & preparing RAMCode - End of preparing flash programming - CPU is running at 16021 kHz.

Regarding your post I’m having a similar problem with internal KE02 EEPROM.

With this utility I have a GUI to erase and program my device. This utility is not intended to be used for production.

#Selected data does not fit into selected flash sectors download#

There is a free-of-charge ‘Lite’ version available for download from Segger. Segger has product named ‘J-Flash’ which is used to Flash and Erase devices outside of an IDE. However, sometimes I really need to clear all my data in FLASH too, and then I need to erase all my FLASH pages on the device. And it does not erase the application data I’m using in non-volatile memory (see “ Configuration Data: Using the Internal FLASH instead of an external EEPROM“). Additionally, it does not do a complete erase of the device: it only programs the pages I’m using in my application.

So downloading twice the same application actually will not touch the FLASH memory at all. Part of that speed is that the Segger firmware checks each FLASH page if it really needs to be programmed, and only then it erases and reprogrammed that page. The Segger J-Link features a very fast programming. What I need is to unprotect the memory and then erase it. ERROR Algo135 Flash Protection Violation about failed FLASH Programming